IATSE 134

Menu

Skip to content
  • Welcome
  • Local 134
    • About IATSE
    • About Our Local
    • Member Resources
  • Contact Us
    • Officers/Staff
    • Hire Local 134
    • Join Us
  • Venues
    • California Theatre
    • Hammer Theatre
    • Levi’s Stadium
    • Montgomery Theatre
    • Mountain Winery
    • San Jose Civic
    • San Jose Center For the Performing Arts
    • San Jose Convention Center
    • San Jose Event Center
    • Santa Clara Convention Center
    • SAP Center
    • Shoreline Amphitheatre
    • Villa Montalvo
  • Join Us

San Jose Center For The Performing Arts

San Jose Center for the Performing Arts

255 S Almaden Blvd
San Jose, CA 95113

Technician Entrance

Entrance on West San Carlos St

Dress Code

Show Blacks for Set up, show and strike. Hard Hats during overhead work. Hi Vis for Truck Loaders

All clothes should be clean, no tears or stains; shirts should be buttoned up, pants pulled up; no open toed shoes.

Work Clothes: Jeans or other work pants; shorts or sleeveless shirts may not be acceptable in certain circumstances.

Show Blacks: Same as work clothes but black; jeans or cargo pants, small logos are acceptable.

Tech Blacks: Collared shirt (polo or button up), small logos may be acceptable; unfaded black jeans or Dockers; black shoes or sneakers.

Dress Blacks: Button up black shirt, no logos; black dockers or dress slacks, polishable shoes.

PPE:

Hard hats: Ansi Z89.1 compliant. Chin straps required for all climbers

High Vis: Class 2 or 3

From the Outline of Workers Obligations

A WORKER AT THE JOB SITE SHALL HAVE THE REQUIRED TOOLS

A Basic Hand Tools required:

Hammer, 8” Adjustable Wrench, Slotted & Phillips Screwdriver, Pliers, Wire Cutters, Knife, and Gloves, Pen or Pencil and Flashlight.

Other specific tools may be required for other specifically assigned work (i.e., riggers, A/V techs, etc.) If this is the case, the appropriate steward will notify you.

Steel toe safety shoes and safety glasses (if you normally wear glasses are strongly recommended and are the responsibility of the worker.

Recommended Tools include:

Tool Belt or Pouch, Battery Powered Screwdriver/Drill, Measuring Tape, Socket, Open End, Box End and/or Ratchet Wrenches.

Failure to have the required tools may result in your replacement on the call.

Required Tools

Electrician’s

Tape Measure
4 in 1 Screw Driver
Crescent Wrench
Ratchet Wrench – 3/8″ drive, 3/8″, 7/16″, 1/2″, 9/16″ deep sockets
Channel Locks
Pliers
Wire Cutters
Allen Set
Pocket Knife
Flashlight
Safety Glasses
Gloves
Pen and Pencil
Black Sharpie
OPTIONAL (but highly recommended):
Voltage Meter
Pin Splitter

Carpenter’s

Tool Belt
Tape Measure (30’-35’)
Hammer
4 in 1 Screw Driver
Screw Gun with Phillips Bit
Crescent Wrench
Ratchet Wrench – 3/8” drive, 3/8″, 7/16″, 1/2″, 9/16″ deep sockets
Channel Locks
Pliers
Vise Grips
Diagonal Cutters
Allen Set
Matt Knife
Flashlight
Safety Glasses
Torpedo Level
Gloves
Pen and Pencil
Black Sharpie

Audio and Video

Flashlight
4 in 1 Screwdriver
Crescent Wrench
Multi-tool
Jewelers Screwdrivers – (Phillips and Flat)
Needle Nose Pliers
Assorted Nut Drivers
Pocket Knife
Circuit Tester
Board Tape or Masking tape
Electrical Tape
Sharpie or other fine point permanent marker
Gloves
Pen and small Pad of Paper

Rigger’s

100’ Rope 5/8” Single or Double Braid
Sheave
Multi Loop
Carabineers
Plumb Laser
Headlamp
Hammer and Lanyard
9/16” Ratchet Wrench
Gloves

Proudly powered by WordPress | Theme: Illustratr by WordPress.com.